[ale] Hauppauge WinTV 150 card and Suse 10 (follow-up)

[Tim Erwin]

Thanks Mike.

I have Suse 10, kernel 2.6.13-15.
My Hauppauge WinTV PVR 150 is in the first PCI slot (I think) and is not
directly connected to my Sound Blaster Live! card in the second PCI slot.

Suse recognized the card, but did not create any /dev/video entries, and the
default TV applications didn't work. XAWTV tries to come up, but then
disappears. KDETV comes up, but is a blank screen with no obvious options to
find out what is wrong. I don't know where to look to see log entries, if
there is such information.

I read somewhere that IVTV was required, so I downloaded
ivtv-0.4.1.tar.gzand installed according to directions i found,
probably on the
ivtvdrivers.org site. (By the way, I just now found another site with more
directions, but haven't tried them yet: www.differentpla.net/422)

I then ran YaST2 to config the card (didn't know exactly what was needed,
however). I changed the loaders default description of the card (which
appeared to be correct already). I changed the card (card 0) to
vendor=Hauppauge, car=WinTV PVR.
I then clicked on expert settings, which allowed me to choose kernel
modules. There are several entries for ivtv that I think were not there
before I did the ivtv install. My last selection here was "ivtv: iTVC15_16
driver". I then chose "not connected to sound card" and "do not use IRC".
When I go back to scan for channels, I get the error:
"The kernel module for TV support could not be loaded. FATAL error inserting
ivtv: /lib/modules/2.6.13-15/default/extra/ivtv.ko: Unknow symbol in module,
or unknown parameter (see dmesg).

Here is my DMESG. You can see a previous choice I made when trying to
configure the card:

ivtv_tveeprom: module not supported by Novell, setting U taint flag.
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 9 (level, low) ->
IRQ 9
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 9, io base 0x00001400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xf4000000
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKD] -> GSI 9 (level, low) ->
IRQ 9
tulip0:  MII transceiver #1 config 1000 status 786d advertising 01e1.
eth0: ADMtek Comet rev 17 at 00011000, 00:03:6D:1A:46:66, IRQ 9.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2048 buckets, 16384 max) - 248 bytes per conntrack
gameport: EMU10K1 is pci0000:00:0e.1/gameport0, io 0x1450, speed 1269kHz
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
NET: Registered protocol family 17
ACPI: Power Button (FF) [PWRF]
0000:00:10.0: tulip_stop_rxtx() failed
eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
IA-32 Microcode Update Driver: v1.14 <tigran at veritas.com>
microcode: CPU0 already at revision 0xe (current=0xe)
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
mtrr: 0xfc000000,0x2000000 overlaps existing 0xfc000000,0x800000
eth0: no IPv6 routers present
powernow: This module only works with AMD K7 CPUs
subfs 0.9
subfs: unsuccessful attempt to mount media (256)
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.101
DST=224.0.0.251LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=7 DF PROTO=UDP
SPT=5353 DPT=5353
LEN=87
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.101
DST=224.0.0.251LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=8 DF PROTO=UDP
SPT=5353 DPT=5353
LEN=87
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.101
DST=224.0.0.251LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=9 DF PROTO=UDP
SPT=5353 DPT=5353
LEN=87
Linux video capture interface: v1.00
ivtv: module not supported by Novell, setting U taint flag.
ivtv: Unknown parameter `ivtv'

I am out of ideas. I've been reading internet search results for several
days now, but haven't found any that seem to help me solve this problem.

Thanks for any suggestions. I would like to get the card working so I can
proceed to setting up MythTV.

-Tim
-------------- next part --------------
An HTML attachment was scrubbed...