[ale] Lite-On 1640

[Christopher Fowler]

Here is an update.

I loaded windows and could not burn their either.  The CD-RW is faulty
and is going back to Ginstar on Tuesday.  I will ask them to replace it
and do a test burn.


On Fri, 2002-06-21 at 15:44, Glenn C. Lasher Jr. wrote:
> On Mon, 17 Jun 2002, Dow Hurst wrote:
> 
> > dev=0,0,0 seems too much like the scsi controller.  Isn't more like 
> > dev=0,1,0 or some such beast?  Is the ide-scsi emulation setup right?
> > Dow
> 
> The controller would most likely be 0,0,7 for all devices 0,0,*.  Thus, 
> older SCSI devices attached to a controller could be given targets of 0-6.  
> 
> Empirically, I can tell you that under ide-scsi, 0,0,0 works if there is 
> not other SCSI interface, otherwise, the other SCSI interfaces get lower 
> interface numbers.  In my particular case, my CD burner is 1,0,0, because 
> I have a low-end Symbios SCSI card in there to connect my scanner.
> 
> cdrecord -scanbus will remove all doubt.
> 
> > 
> > cfowler wrote:
> > 
> > >Is there a secret to getting the LITE-ON 1640 CD-RW to work under
> > >RH7.3?  Here is what I get:
> > >
> > >
> > >
> > >[root at cfowler tmp]# cdrecord -v -speed=2 -dev=0,0,0 -data ./l.iso
> > >Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
> > >TOC Type: 1 = CD-ROM
> > >scsidev: '0,0,0'
> > >scsibus: 0 target: 0 lun: 0
> > >Linux sg driver version: 3.1.22
> > >Using libscg version 'schily-0.5'
> > >atapi: 1
> > >Device type    : Removable CD-ROM
> > >Version        : 0
> > >Response Format: 1
> > >Vendor_info    : 'LITE-ON '
> > >Identifikation : 'LTR-16102B      '
> > >Revision       : 'OS06'
> > >Device seems to be: Generic mmc CD-RW.
> > >Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> > >Driver flags   : SWABAUDIO
> > >Drive buf size : 1966272 = 1920 KB
> > >FIFO size      : 4194304 = 4096 KB
> > >Track 01: data    0 MB         padsize: 280 KB
> > >Total size:       0 MB (00:04.02) = 302 sectors
> > >Lout start:       1 MB (00:06/02) = 302 sectors
> > >Current Secsize: 2048
> > >ATIP info from disk:
> > >  Indicated writing power: 4
> > >  Is not unrestricted
> > >  Is not erasable
> > >  Disk sub type: Medium Type A, high Beta category (A+) (3)
> > >  ATIP start of lead in:  -11849 (97:24/01)
> > >  ATIP start of lead out: 359848 (79:59/73)
> > >Disk type:    Long strategy type (Cyanine, AZO or similar)
> > >Manuf. index: 25
> > >Manufacturer: Taiyo Yuden Company Limited
> > >Blocks total: 359848 Blocks current: 359848 Blocks remaining: 359546
> > >Starting to write CD/DVD at speed 2 in write mode for single session.
> > >Last chance to quit, starting real write in 0 seconds. Operation starts.
> > >Waiting for reader process to fill input buffer ... input buffer ready.
> > >Performing OPC...
> > >Starting new track at sector: 0
> > >Track 01:   0 of   0 MB written.
> > >Track 01: writing 280 KB of pad data.
> > >Track 01: Total bytes read/written: 327680/614400 (300 sectors).
> > >Writing  time:   27.970s
> > >Fixating...
> > >
> > >cdrecord: Input/output error. close track/session: scsi sendcmd: no
> > >error
> > >CDB:  5B 00 02 00 00 00 00 00 00 00
> > >status: 0x2 (CHECK CONDITION)
> > >Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 72 00 00 00
> > >Sense Key: 0x3 Medium Error, Segment 0
> > >Sense Code: 0x72 Qual 0x00 (session fixation error) Fru 0x0
> > >Sense flags: Blk 0 (not valid)
> > >cmd finished after 113.069s timeout 480s
> > >cmd finished after 113.069s timeout 480s
> > >Fixating time:  113.095s
> > >cdrecord: fifo had 6 puts and 6 gets.
> > >cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
> > >[root at cfowler tmp]#
> > >
> > >
> > >Do I need to run Windows to burn on this thing?
> > >
> > >
> > >
> > >
> > >---
> > >This message has been sent through the ALE general discussion list.
> > >See http://www.ale.org/mailing-lists.shtml for more info. Problems should be 
> > >sent to listmaster at ale dot org.
> > >
> > >
> > >  
> > >
> > 
> > 
> > ---
> > This message has been sent through the ALE general discussion list.
> > See http://www.ale.org/mailing-lists.shtml for more info. Problems should be 
> > sent to listmaster at ale dot org.
> > 
> 
> -- 
> glasher at nycap.rr.com
> You've been programmed by the Illuminati not to see the word "".
> 
> 
> ---
> This message has been sent through the ALE general discussion list.
> See http://www.ale.org/mailing-lists.shtml for more info. Problems should be 
> sent to listmaster at ale dot org.
> 
> 
> 



---
This message has been sent through the ALE general discussion list.
See http://www.ale.org/mailing-lists.shtml for more info. Problems should be
sent to listmaster at ale dot org.