[ale] modem set-up, love to hate it

[Sage]

On Thu, 08 Mar 2001 21:17:18 -0700 "Joseph A. Knapka" <jknapka at earthlink.net> wrote:

Two things:

(1) You almost certainly have two serial ports built into
your motherboard (if this is not the case I'll eat... well,
something unexpected). They will be configured as ttyS00 and
ttyS01 unless you disable them in the BIOS settings (there's
probably a "built-in peripherals" menu or something when you
enter the BIOS setup screens at boot time).

I haven't much experience with messing about with the BIOS. Are you suggesting that I change something there? (sorry for being a bit thick-headed tonight, it's kinda past my bedtime)



(2) If you've got a Plug-n-Pray device, it *must* be configured
properly before you can use it. 

We disabled pnp, tried ttyS01, ttyS03 settings with IRQ 3, got the "Conflict I/O...2f8" msg. Tried both with IRQ 9, which the system wouldn't allow (defaulted to 3). All combinations gave us "modem is busy" error message when trying to connect.


If you don't let the kernel
or isapnp assign the device an IRQ and IO ports, you lose.
If your box has a PnP BIOS it will try to configure all the
PnP devices it finds, I think, and in that case I expect the
kernel would use the BIOS settings (so you shouldn't need
to worry about it), but I'm not sure.

I don't even know if the 2.4 PnP stuff works; I know the
earlier kernel PnP support was pretty twitchy, so I always
just used isapnp. This is not very simple or well-documented,
but it works, and I'm sure folks on the list can help you
out if need be.

Thank you very much for your help, Joe. Okay, can anyone out there help me out with a pnp modem configuration? Using isapnp got me an error message of, "You don't seem to be connected to the Internet". (Well, no shit, really?!!?!?)

-Indira

HTH,

-- Joe

Sage wrote:
> 
> And here again is another nasty.
> 
> Bought a new box last week. Installed Mandrake 7.2, which I will probably run over with Slackware. The GUI is MUCH too, well, fluffy.
> 
> ANYWAY, once installed, dmesg showed a ttyS00, a ttyS01, and a isapnp modem (Ack!). ttyS00 is on/at IRQ4 (I am thinking this is the mouse), and ttyS01 is at IRQ3 (which I had thought was supposed to be the modem).
> 
> Ditzed the pnp crap immediately. Tried every combo of tty's on the hardware, even tried changing the IRQ to 9 (when I did that, the system changed it back to three upon rebooting, anyone know why?). The system recognizes the new port setting, but will not put the IRQ where I set it on the hardware.
> 
> What on earth could ttyS01 be? It is causing a "Conflict I/O...2f8" error message from the BIOS, before LILO comes up. I assume here that is because two of the IRQ's are the same. I have checked, and my husband has checked again, and there is nothing else on a serial port, except the mouse. I keep getting "modem is busy" msg.
> 
> It is NOT a winmodem, had to pay extra for that, too. It is a TI, 56K V.90/X2.
> 
> Can anyone help me out here, or should I just take the stupid thing out to the back yard and shoot it?
> 
> Any help would be appreciated. I've called several friends who are Linux users, and they haven't a clue.
> 
> Thanks.
> 
> -Indira
> 
> 
> --
> To unsubscribe: mail majordomo at ale.org with "unsubscribe ale" in message body.

-- Joe Knapka
--
To unsubscribe: mail majordomo at ale.org with "unsubscribe ale" in message body.